Human vibration measurement has never been easier with this hand arm and whole body system. Along with the Svantek SV106 six channel human vibration meter and analyser this measurement system can simultaneously measure vibration levels for both hands or tri-axial SEAT transmission. The price includes an SV105 Hand-arm Tri-axial Accelerometer.
Using the computational power of a digital signal processor the SV106 can measure real-time single and third octave levels along with the required vibration measurements for ISO 2631 and ISO 5349, including RMS, Peak, Peak to Peak, VDV, MTV, A(8) and Dose, with all required weighting filters and band limiting filters for HVM measurements.
Built in 16MB non-volatile memory and additional slot for an external Micro SD card (kit is supplied with a 4GB card) can record data for time history logging and time domain signal recording. Results and data can then be easily downloaded to a PC for for analysis. The PC software can even be used to set up the vibration meter prior to use.
Using the SV38V vibration seat pad makes whole-body vibration measurements easier and can be placed directly on a seat cushion, a floor or fixed to the back of the seat.
The SV105 tri-axial accelerometer enables easy measurement of hand-arm vibration regardless of the tool being used.
The six channel dual input meter allows for 2 x SV105 tri-axial accelerometers to be used to measure both hands simultaneously. Using a combination of 1 x SV105 accelerometer and 1 x SV38V seat pad accelerometer is also possible providing simultaneous Hand-arm and Whole Body measurements. Kit is supplied with a single SV105 accelerometer as standard.
Features:
Supplied with:
Using the computational power of a digital signal processor the SV106 can measure real-time single and third octave levels along with the required vibration measurements for ISO 2631 and ISO 5349, including RMS, Peak, Peak to Peak, VDV, MTV, A(8) and Dose, with all required weighting filters and band limiting filters for HVM measurements.
Built in 16MB non-volatile memory and additional slot for an external Micro SD card (kit is supplied with a 4GB card) can record data for time history logging and time domain signal recording. Results and data can then be easily downloaded to a PC for for analysis. The PC software can even be used to set up the vibration meter prior to use.
Using the SV38V vibration seat pad makes whole-body vibration measurements easier and can be placed directly on a seat cushion, a floor or fixed to the back of the seat.
The SV105 tri-axial accelerometer enables easy measurement of hand-arm vibration regardless of the tool being used.
The six channel dual input meter allows for 2 x SV105 tri-axial accelerometers to be used to measure both hands simultaneously. Using a combination of 1 x SV105 accelerometer and 1 x SV38V seat pad accelerometer is also possible providing simultaneous Hand-arm and Whole Body measurements. Kit is supplied with a single SV105 accelerometer as standard.
Features:
- Tri-Axial vibration system and analyser with optional whole-body vibration
- Measures vibration levels meeting ISO 8041:2005, ISO 2631-1,2&5 (including VDV and MTVV) and ISO 5349
- Dual input with 2 profiles with each channel
- Time domain signal recording
- Real time single and third octave measurements
- Advanced data logger with spectral analysis
- Micro SD card for mass data storage
- Easy to use interface with colour display
Supplied with:
- 1x 6 channel human vibration meter
- 1x SV105 Hand arm adaptor with tri-axial accelerometer
- 1x Whole body seat accelerometer (Optional extra)
- 1x Carry case for vibration meter and accessories
- 1x SvanPC++ Software for data viewing and analysis
SV106 Human Vibration Meter
Standards:
ISO 8041:2005, ISO 2631-1,2&5, ISO 5349
Meter Mode:
RMS, VDV, MTVV or Max, Peak, Peak-Peak, Vector, A(8), Dose, ELV, EAV
Simultaneous measurement in six channels with independent set of filters and detector constants
Filters:
Wd, Wk, Wm, Wb (ISO 2631) and Wh (ISO 5349) and Band Limiting filters
RMS & RMQ Detectors:
Digital true RMS & RMQ detectors with Peak detection, resolution 0.1 dB Time constants from 100 ms to 10 s
Data Logger:
Time-history data including meter mode results and spectra (option)
Time Domain Recording:
Simultaneous x, y, z time-domain signal recording, sampling frequency selectable: 375 Hz, 3 kHz or 6 kHz (option)
Analyser:
1/1 octave real-time analysis with centre frequencies from 0.5 Hz to 2000 Hz
1/ octave real-time analysis with centre frequencies from 0.4 Hz to 2500 Hz
Measurement Range:
Transducer dependent:
0.01 ms2 RMS ÷ 50 ms2 Peak (with SV 38V and Wd filter)
0.1 ms2 RMS ÷ 5000 ms2 Peak (with SV 50 and Wh filter)
Frequency Range:
0.1 Hz ÷ 2000 Hz
Input:
2 x LEMO 5-pin: six channels IEPE type or Direct and two channels for force transducers
Dynamic Range:
90 dB
Force Range:
0.2 N ÷ 100 N (dedicated channels for force transducers)
Sampling Rate:
6 kHz
Memory:
Internal 16 MB non-volatile memory
Micro SD flash card slot
Interfaces:
USB 1.1 Client, Extended I/O - AC output (1 V Peak) or Digital Input/Output (Trigger - Pulse)
Power supply:
Four AA batteries (alkaline) - operation time > 12 h (6.0 V / 1.6 Ah)2
Four AA rechargeable batteries (not included) - operation time > 16 h (4.8 V / 2.6 Ah)2
USB interface - 500 mA HUB
Environmental Conditions:
Temperature from -10°C to 50°C
Humidity up to 90% RH, non-condensed
Dimensions:
140 x 83 x 33 mm (without accelerometer)
Weight:
Approx. 390 grams including batteries (without accelerometer)
SV105 Accelerometer
Performance:
Number of axis: 3
Sensitivity (± 5 %): 10.2 mV/(m/s2) at 15.915 Hz, HP1
Measurement range: 0.024 ms-2 RMS,Wh ÷ 180 ms-2 PEAK
Frequency response (± 3 dB): 1 Hz ÷ 2763 Hz
Resonant frequency: 5.5 kHz (MEMS transducer)
Electrical noise: < 240 µV RMS, Wh weighting, < 2.2 mV RMS, HP1 weighting
Electrical:
Supply current: < 5,0 mA
Supply voltage: 5.2 V ÷ 16 V
Bias voltage (IEPE): 2,5 V ± 0.05 V
Output impedance: 51 Ω
Charge / discharge time constant (start-up time): 30 sec. typ.
TEDS memory: installed (power supply pin)
Environmental Conditions:
Maximum vibration: 980 m/s2 shock survival for MEMS sensor
Temperature coefficient: <+0.012 dB/°C
Temperature: from -10°C to +50°C
Humidity: up to 90 % RH, non-condensed
Physical:
Sensing element: MEMS
Cable: integrated 1.4 meters long
Connector: LEMO 5-pin plug (SV 106 compatible)
Dimensions: 69.6 mm x 31.4 mm dimension; thickness from 8.3 mm to 15 mm
Weight: 50-60 grams (including cable and one of vibration contact adapters)
Standards:
ISO 8041:2005, ISO 2631-1,2&5, ISO 5349
Meter Mode:
RMS, VDV, MTVV or Max, Peak, Peak-Peak, Vector, A(8), Dose, ELV, EAV
Simultaneous measurement in six channels with independent set of filters and detector constants
Filters:
Wd, Wk, Wm, Wb (ISO 2631) and Wh (ISO 5349) and Band Limiting filters
RMS & RMQ Detectors:
Digital true RMS & RMQ detectors with Peak detection, resolution 0.1 dB Time constants from 100 ms to 10 s
Data Logger:
Time-history data including meter mode results and spectra (option)
Time Domain Recording:
Simultaneous x, y, z time-domain signal recording, sampling frequency selectable: 375 Hz, 3 kHz or 6 kHz (option)
Analyser:
1/1 octave real-time analysis with centre frequencies from 0.5 Hz to 2000 Hz
1/ octave real-time analysis with centre frequencies from 0.4 Hz to 2500 Hz
Measurement Range:
Transducer dependent:
0.01 ms2 RMS ÷ 50 ms2 Peak (with SV 38V and Wd filter)
0.1 ms2 RMS ÷ 5000 ms2 Peak (with SV 50 and Wh filter)
Frequency Range:
0.1 Hz ÷ 2000 Hz
Input:
2 x LEMO 5-pin: six channels IEPE type or Direct and two channels for force transducers
Dynamic Range:
90 dB
Force Range:
0.2 N ÷ 100 N (dedicated channels for force transducers)
Sampling Rate:
6 kHz
Memory:
Internal 16 MB non-volatile memory
Micro SD flash card slot
Interfaces:
USB 1.1 Client, Extended I/O - AC output (1 V Peak) or Digital Input/Output (Trigger - Pulse)
Power supply:
Four AA batteries (alkaline) - operation time > 12 h (6.0 V / 1.6 Ah)2
Four AA rechargeable batteries (not included) - operation time > 16 h (4.8 V / 2.6 Ah)2
USB interface - 500 mA HUB
Environmental Conditions:
Temperature from -10°C to 50°C
Humidity up to 90% RH, non-condensed
Dimensions:
140 x 83 x 33 mm (without accelerometer)
Weight:
Approx. 390 grams including batteries (without accelerometer)
SV105 Accelerometer
Performance:
Number of axis: 3
Sensitivity (± 5 %): 10.2 mV/(m/s2) at 15.915 Hz, HP1
Measurement range: 0.024 ms-2 RMS,Wh ÷ 180 ms-2 PEAK
Frequency response (± 3 dB): 1 Hz ÷ 2763 Hz
Resonant frequency: 5.5 kHz (MEMS transducer)
Electrical noise: < 240 µV RMS, Wh weighting, < 2.2 mV RMS, HP1 weighting
Electrical:
Supply current: < 5,0 mA
Supply voltage: 5.2 V ÷ 16 V
Bias voltage (IEPE): 2,5 V ± 0.05 V
Output impedance: 51 Ω
Charge / discharge time constant (start-up time): 30 sec. typ.
TEDS memory: installed (power supply pin)
Environmental Conditions:
Maximum vibration: 980 m/s2 shock survival for MEMS sensor
Temperature coefficient: <+0.012 dB/°C
Temperature: from -10°C to +50°C
Humidity: up to 90 % RH, non-condensed
Physical:
Sensing element: MEMS
Cable: integrated 1.4 meters long
Connector: LEMO 5-pin plug (SV 106 compatible)
Dimensions: 69.6 mm x 31.4 mm dimension; thickness from 8.3 mm to 15 mm
Weight: 50-60 grams (including cable and one of vibration contact adapters)
